| 24-C3 |
Three years of calibration coverage based on the R&S recommended calibration interval - includes test data. |
| 24-C5 |
Five years of calibration coverage based on the R&S recommended calibration interval - includes test data. |
| 24-R3 |
Three years of depot repair coverage, including recalibration and test data if necessary to complete a repair |
| 24-R5 |
Five years of depot repair coverage, including recalibration and test data if necessary to complete a repair |
| B1 |
Mixed signal option, 400 MHz, for RTOs without trigger output |
| B1 |
Mixed Signal option 400 MHz, for RTOs with trigger output |
| B101 |
Memory upgrade 50MSa per channel |
| B102 |
Memory upgrade 100MSa per channel |
| B19 |
Hard disk for exchange incl. firmware |
| B4 |
OCXO 10MHz |
| DCV-2 |
Documentation of calibration values |
| DCV-ZP |
Printout of DCV (additional, in combination with DCV-Option only) |
| K1 |
I2C/SPI serial decoding (software license) |
| K2 |
RS-232/UART serial decoding (software license) |
| K3 |
CAN/LIN serial trigger and decoding (software license) |
| K4 |
GH RTO-K4 FLEXRAY TRIGGER & DECODE |
| RT-ZA1 |
Accessory kit for passive voltage probes RT-ZP10/RTM-ZP10 (2.5 mm tip style) |
| RT-ZA2 |
Spare accessory set for active voltage probe RT-ZS10E/10/20/30 |
| RT-ZA3 |
Pin set for active voltage probe RT-ZS10E/10/20/30 (20 signal pins; 5 ground pins, pogo; |
| RT-ZA4 |
Mini clips (10 pce, probe accessory) |
| RT-ZA5 |
Micro clips (4 pce, probe accessory) |
| RT-ZA6 |
Lead set (5*6cm/2.4", 5*15cm/5.9"; probe accessory) |
| RT-ZA9 |
N(m) adapter for connection of R&S®RT-Zx probes to spectrum and network analyzers with N(f) connectors; |
| RT-ZB1 |
Demo board for digital signal analysis with oscilloscopes; test interfaces: I2C,SPI,RS232,CAN,LIN, |
| RT-ZD30 |
3,0 GHz voltage probe, active, differential, 1.2m cable, 1 MOhm, 0,5 pF including accessories |
| RT-ZP10 |
500MHz voltage probe, passive, 10:1, 10MOhm, 9.5pF, 400V max., 1.3m cable, BNC connector, 2.5mm tip style, |
| RT-ZS10 |
1.0GHz voltage probe, active, single-ended, 1MOhm, 0.8pF, ProbeMeter, MicroButton, 1.2m cable; |
| RT-ZS10E |
1.0GHz voltage probe, active, single-ended, 1MOhm, 0.8pF, 1.2m cable; including accessories |
| RT-ZS20 |
1.5GHz voltage probe, active, single-ended, 1MOhm, 0.8pF ProbeMeter, Micro button, 1.2m cable; |
| RT-ZS30 |
3.0GHz voltage probe, active, single-ended, 1MOhm, 0.8pF, ProbeMeter, Micro button, 1.2m cable; |
| Z1 |
Front cover (for RTO oscilloscopes) |
| Z3 |
Soft case for RTO oscilloscopes and accessories |
